Maritime

First type approval of aluminium cables and connectors now in place

The shipping industry is observing that copper cables are being replaced with aluminium cables. The cost and weight savings can be significant – together with easier installation and lower fuel costs. To support its customers, DNV GL has developed the first type approval scheme for the use of aluminium cables and their connectors on board vessels.

Aluminium cable

Relevant for ship owners and managers, yards, suppliers, design offices and flag states.

Background

Traditionally, power cables for marine use have been made with copper. Copper is an ideal electrical conductor, but the price of copper has been rising sharply over the last decades, adding costs to the maritime industry. Today, the price of aluminium is roughly one third of the copper price. At the same time, electric propulsion, batteries and hybrid solutions are becoming more widespread in shipping. This is increasing the demand for more economical power cables.

Properties and benefits

Aluminium’s lower conductivity means that a thicker cable is required, but this is compensated for by an overall lower weight. For example, a typical offshore support vessel may have 60 tonnes of large copper cables installed. If these were replaced with aluminium, the weight would be reduced to less than 30 tonnes. Even with the price of special high-quality terminations factored in, the overall estimated saving from switching to aluminium from copper may be more than 50 per cent.

Lighter cables also result in easier installation for the ship builder, further savings on cable trays, less strain on workers and reduced transport costs. Finally, a vessel with aluminium rather than copper cables is lighter and more fuel efficient – resulting in lower operational costs over the vessel’s lifetime.

On a fast ferry where several tonnes of copper weight could be replaced with increased cargo capacity, this would generate added revenue on every trip. Or, alternatively, the weight savings would result in reduced fuel consumption, reduced cost and lower emissions.

Testing and possible issues

The use of aluminium cables has been tested for the past three years in a pilot installation onboard the Olympic Subsea owned and managed, Olympic Artemis, a multipurpose offshore support vessel. The cables have been used to supply power to one of the vessel’s thrusters.

Recently, DNV GL experts, together with representatives from the cable manufacturer, checked the aluminium cables on board Olympic Artemis with a thermographic camera. The survey confirmed perfect connections after more than 11,000 operating hours at sea.

Aluminium has some special properties which can create potential risk for bad electrical contact: Aluminium oxide on the surface must be penetrated to make good contact. Aluminium is soft, and so-called cold flow may cause material to loosen under pressure. Both these issues have been considered and tested in the approved terminations. Furthermore, aluminium cables are intended for fixed installations only – aluminium cables are not designed for moving applications.

Until recently, DNV GL rules did not accept the use of aluminium cables on board vessels. The IEC (International Electrotechnical Commission) has not yet implemented aluminium conductors in their standards for marine cables, but are following the development.

Cables installed on ships are exposed to vibration. A salty atmosphere increases risk of corrosion. Together with our industry partners, DNV GL has carried out thorough environmental, electric and mechanical testing, including vibration and salt mist tests. This, combined with the three-year successful pilot installation on board Olympic Artemis, makes DNV GL confident that aluminium cables provide an “equivalent safety level” compared with conventional copper cables when type approved equipment is used and installed according to the instructions.

Recommendations

The costs for power cables can be reduced by replacing expensive copper conductors with aluminium. DNV GL recommends the consideration of aluminium cables on vessels where large power cables are needed. For installations in ships where weight is important, aluminium cables are indeed interesting due to reduced operational costs. From an HSE perspective, lighter cables mean less strain on workers installing the cables and jobs can be done faster.

References

Contact

For customers:
DATE - Direct Access to Technical Experts via My Services

Otherwise:
Email us at DNV GL Electrical Systems

Appendix

Information about installation - see page 2 on PDF document available below.

29 April 2022

IMO maritime safety committee (MSC 105)

The 105th session of the IMO’s Maritime Safety Committee (MSC) was held remotely from 20 to 29 April. A wide range of topics was on the agenda, including the safety of ships carrying industrial personnel, the safety of ships relating to the use of fuel oil, and the consideration of a regulatory framework for maritime autonomous surface ships. Requirements reflecting modern systems for maritime distress and safety communication were adopted and interim guidelines for the safety of ships using fuel cell power installations were approved. The development of interim guidelines for ships using ammonia as fuel were initiated.

  • Maritime
11 April 2022

IMO sub-committee on pollution prevention and response (PPR9)

The 9th session of the IMO’s Sub-Committee on Pollution Prevention and Response (PPR 9) was held remotely from 4 to 8 April 2022. A wide range of topics was on the agenda, including biofouling, ballast water management, black carbon, sewage treatment and marine plastic litter. PPR agreed on draft guidelines on risk and impact assessments of the discharge water from exhaust gas cleaning systems when considering local or regional regulations.

  • Maritime
24 March 2022

SEEMP Part III and the upcoming SEEMP Generator from DNV

Since 2019 ships of 5,000 GT and above have been reporting their fuel oil consumption data mandated by the IMO DCS. From 2023, cargo, cruise and RoPax ships must calculate CII with a required rating of C or better. This means some ships will have to improve their carbon intensity. A verified Ship Operational Carbon Intensity Plan, or SEEMP Part III, is to be kept on board from 1 January 2023 to document how you plan to achieve your CII targets. This statutory news provides an update on the SEEMP Part III and recommends next steps.

  • Maritime
07 March 2022

IMO Sub-Committee on Ship Systems and Equipment (SSE 8)

The 8th session of the IMO’s Sub-Committee on Ship Systems and Equipment (SSE 8) was held remotely from 28 February to 4 March. SSE 8 finalized draft new ventilation requirements for lifeboats and liferafts, and draft new guidelines for the design, construction, installation, testing, maintenance and operation of lifting appliances and anchor handling winches. Good progress was made on the new mandatory requirements to minimize the incidence and consequences of fires on ro-ro passenger ships, and on the work to improve the safety of commercial diving operations.

  • Maritime
14 February 2022

IMO Sub-Committee on Human Element, Training and Watchkeeping (HTW 8)

The 8th session of the IMO’s Sub-Committee on Human Element, Training and Watchkeeping (HTW 8) was held remotely from 7 to 11 February. Highlighting the human element as a key factor both for safety and environmental protection, HTW 8 agreed on a revised checklist for considering the human element in the review, development and implementation of new and existing IMO requirements. HTW 8 also agreed on amendments to the STCW Convention and Code to accommodate the use of seafarers’ electronic certificates and documents.

  • Maritime
View all